# CBCT voxel size: what 0.3 mm means for sharpness

> Voxel size is the grid a CBCT scan is stored on. Sharpness is set by more than the grid, and a larger voxel is often a deliberate choice to lower dose.

- URL: https://jawviewer.com/blog/cbct-voxel-size-sharpness
- Category: Understanding your scan
- Published: 2026-11-21
- Updated: 2026-11-21
- Author: Jaw Viewer
- Reading time: 5 min
- Tags: cbct, image-quality, measurements, dicom

## Key points

- Voxel size is the edge length of one grid cell in a CBCT scan, for example 0.3 mm. It sets the finest grid the scan can hold, not how sharp the picture is.
- Published CBCT resolution runs from 0.6 to 2.8 line pairs per millimetre. A grid of 0.3 mm voxels can hold at most about 1.7 line pairs per millimetre (our arithmetic).
- A review of implant studies found that voxels of 0.3 to 0.4 mm give images of acceptable quality for implant treatment planning.
- Low-dose CBCT protocols are made partly by using larger voxels. A review of 16 studies found objective measurements similar to higher-resolution protocols.

Voxel size is the length of one edge of a single grid cell in a CBCT scan, usually between 0.1 and 0.4 mm. It sets the finest grid the scan can store. The sharpness you actually see depends on more than that grid.

The voxel size printed on your scan helps you read the resolution figures in [what a CBCT scan shows](https://jawviewer.com/blog/what-a-cbct-scan-shows.md). A larger voxel can also be a deliberate choice to reduce dose.

## What is a voxel?

A voxel is a three-dimensional pixel. A scan is a block of them stacked in rows, columns and layers, and each holds one grey value. Voxel size is how long each cell is in millimetres. The size is stored in the file header of the DICOM files ([what is inside a DICOM file](https://jawviewer.com/blog/what-is-inside-a-dicom-file.md)).

Jaw Viewer reads the voxel size from your files and shows it in the footer and in the scan details. Next to it the viewer notes that readings are good to about plus or minus one voxel.

## Is the grid the same as sharpness?

No. The grid is a ceiling. The review of published measurements by Brüllmann and Schulze lists three things that decide the effective resolution: the two-dimensional detector, the three-dimensional reconstruction and patient movement during the scan.[1] Voxel size is a setting chosen on top of those, and it cannot restore detail they lose.

Resolution is usually quoted in line pairs per millimetre (lp/mm). The review found visual measurements between 0.6 and 2.8 lp/mm, with a median of 1.7 lp/mm, and expects just above 1 lp/mm in real scans of living patients.[1]

A grid needs at least two voxels to show one line pair, a dark cell and a light cell (this is our arithmetic, the sampling limit). That puts a ceiling on each voxel size:

| Voxel size | Most line pairs the grid can hold | Narrowest line pair |
| --- | --- | --- |
| 0.2 mm | 2.5 lp/mm | 0.4 mm |
| 0.3 mm | about 1.7 lp/mm | 0.6 mm |
| 0.4 mm | 1.25 lp/mm | 0.8 mm |

The median published resolution of 1.7 lp/mm matches a grid of about 0.3 mm. A realistic 1 lp/mm in a patient scan sits near what a 0.5 mm grid could hold. So in typical scans the voxel size and the physics are in the same range, and a finer grid than the image can deliver gains little.

> Reading the table
>
> The middle column is a limit set by the grid alone. The published figures above it come from measurements on scanners, and they include the losses from detector, reconstruction and movement.

## What do 0.3 to 0.4 mm voxels give you?

A systematic review of 22 studies, 2 clinical and 20 ex vivo, looked at linear measurements on CBCT images used before implant treatment. It reports a wide range of error, with both over- and underestimation compared with a reference. It also states that a voxel size of 0.3 to 0.4 mm is adequate for images of acceptable diagnostic quality in implant treatment planning.[2]

The same review advises a 2 mm safety margin to neighbouring anatomy, and says that patient motion, metal artefacts, device-specific exposure settings and software are likely to reduce accuracy in clinical practice.[2] That is the reason a measurement is read as a range. Our article on [how accurate CBCT measurements are](https://jawviewer.com/blog/how-accurate-are-cbct-measurements.md) goes through it.

0.6 to 2.8 lp/mm

published CBCT resolution range[1]

0.3 to 0.4 mm

voxel size judged adequate for implant treatment planning[2]

2 mm

safety margin advised to adjacent anatomy[2]

## Why would a scan use larger voxels?

Because a coarser grid lowers dose. A systematic review of 16 studies on low-dose CBCT protocols found that these protocols are made by reducing tube voltage, tube current, resolution through a larger voxel, exposure time and the scanning path.[3] The same review found that low-dose protocols performed similarly to higher-resolution ones on objective measurements, with the adverse effects mostly on subjective impressions of image quality.[3]

So a scan with 0.4 mm voxels next to one with 0.2 mm voxels may reflect a decision about dose for the question being asked. The review looked at implant work, so it does not tell you the same holds for every task. Dose levels are in our [radiation dose](https://jawviewer.com/blog/radiation-dose-cbct-vs-ct.md) article.

There is a cost in file size too. Halving the voxel size gives eight times as many voxels in the same volume (our arithmetic), so a scan at 0.2 mm is much larger on disk than one at 0.4 mm. The size of the volume also depends on the [field of view](https://jawviewer.com/blog/cbct-field-of-view-explained.md).

## Why does a scan look pixelated up close?

Every voxel holds one grey value, so a thin structure only a voxel or two wide shows as a few steps of brightness. That is the stored data. Scanner movement or metal can add blur or streaks on top of the grid ([artefacts](https://jawviewer.com/blog/cbct-artefacts-streaks-near-metal-motion.md)), which looks different from plain blockiness.

For example, a distance across 20 voxels of 0.3 mm is 6 mm, and placing a point one voxel off moves the result by about 0.3 mm (our arithmetic). Point placement and the scan's own noise come on top, so the voxel size is a floor for the uncertainty, not a total. The [measuring guide](https://jawviewer.com/guide/view-and-measure.md) shows how to place points on the slices.

This is general information, not medical advice. Jaw Viewer is not a medical device. Talk to your surgeon, orthodontist or radiologist about your own case.

## Questions and answers

### What does a voxel size of 0.3 mm mean?

Each cell of the scan's three-dimensional grid is 0.3 mm along every edge. Distances in the scan are counted in steps of that size. It does not mean details of 0.3 mm are always visible.

### Is a smaller voxel size always sharper?

Not always. A review lists the detector, the reconstruction and patient movement as further limits on the real resolution. A finer grid cannot add detail those steps lose.

### Why do some scans use a larger voxel size?

A review of 16 studies reports that low-dose protocols come partly from larger voxels, along with lower exposure settings, shorter time and a shorter scan path.

### Why does my CBCT look pixelated when I zoom in?

Zoomed far enough, a scan shows its grid, because each voxel holds a single grey value. The blockiness is the stored data, and it comes from the voxel size.

## Terms used

- **CBCT**: Cone beam computed tomography. A scanner that rotates once around the head and records a cone-shaped X-ray beam, common in dentistry and jaw surgery.
- **Voxel**: A three-dimensional pixel. A scan is a grid of voxels, each with one grey value.
- **Grey value**: The brightness number stored for a voxel. On a CBCT scan it is not a calibrated measure of density.
- **DICOM**: The file format and standard that medical scanners use for images and their details.
- **Line pair**: One dark line and one light line side by side. Spatial resolution is often given in line pairs per millimetre.

## Sources

1. Brüllmann D, Schulze RK (2015). Spatial resolution in CBCT machines for dental/maxillofacial applications, what do we know today?. Dentomaxillofac Radiol, vol. 44, pp. 20140204. https://doi.org/10.1259/dmfr.20140204
2. Fokas G, Vaughn VM, Scarfe WC et al. (2018). Accuracy of linear measurements on CBCT images related to presurgical implant treatment planning: a systematic review. Clin Oral Implants Res, vol. 29 Suppl 16, pp. 393-415. https://doi.org/10.1111/clr.13142 22 studies, 2 clinical and 20 ex vivo.
3. Kaaber L, Matzen LH, Schropp L et al. (2024). Low-dose CBCT protocols in implant dentistry: a systematic review. Oral Surg Oral Med Oral Pathol Oral Radiol, vol. 138, pp. 427-39. https://doi.org/10.1016/j.oooo.2024.03.013 16 studies.

---

Jaw Viewer (https://jawviewer.com). Page index for AI tools: https://jawviewer.com/llms.txt. Not a medical device.
