# How to measure on a CT or CBCT scan

> Two points make a distance, three an angle, a closed outline an area. How each measurement works on a scan, in which view to place it, and what to check.

- URL: https://jawviewer.com/blog/how-to-measure-on-a-ct-scan
- Category: Measurements explained
- Published: 2026-11-21
- Updated: 2026-11-21
- Author: Jaw Viewer
- Reading time: 5 min
- Tags: cbct, measurements, dicom

## Key points

- A distance needs two points, an angle three with the middle one at the vertex, an area a closed outline in one slice, and a volume one click inside a space.
- In 28 dry skulls, measuring on axial slices gave an average error under 0.6% on test wires, against under 1.2% on panoramic reconstructions.
- A 2018 review of 22 studies (2 clinical, 20 ex vivo) found a wide error range in CBCT linear measurements, both over and under the true value.
- A 2024 meta-analysis of low-dose protocols pooled a measurement error of -0.24 mm (95% CI -0.52 to 0.04), a slight tendency to read short.

A measurement on a CT or CBCT scan is built from points you place yourself. Two points give a distance, three give an angle, a closed outline in one slice gives an area, and a click inside an air space gives a volume. The scan stores the spacing between its voxels, so the software can turn those points into millimetres.

## Before you measure

Open the scan and look at it first. If the files are still on a disc, [opening the scan from a disc](https://jawviewer.com/blog/open-cbct-scan-from-cd.md) comes first. To read the three slice directions, see [axial, coronal and sagittal views](https://jawviewer.com/blog/axial-coronal-sagittal-views-explained.md).

A voxel is the smallest cell of the scan. Its size sets how finely an edge can be located, and the distance between voxel centres is what the software multiplies by to get millimetres. For what else limits detail, see [what a CBCT scan shows](https://jawviewer.com/blog/what-a-cbct-scan-shows.md).

## Measure a distance and an angle

1. Choose the tool
   Open Measure and select Distance (shortcut D). Angle is next to it (shortcut N).
2. Place the points
   For a distance, click the first point, then the second. For an angle, click three points, the middle one at the vertex. Check each point in the other views before you trust it.
3. Read the result
   The value appears in the measurement list, in millimetres for a distance and in degrees for an angle. If a point is misplaced, undo and place it again.

*Figure: A distance measurement across the sample lower jaw, shown in the slices and in 3D. The same line in every view of the public sample scan. Sample scan "CBCT-MR Head (DZ-CBCT)", 3D Slicer sample data, donated for use without restrictions. Screenshot from Jaw Viewer.*

The line appears in the slices and on the bone at the same time. Check a point placed on the 3D surface against the slice it lies in. The surface is drawn from the scan, and changing its preset can move where the visible edge sits. The slice is the safer place to put a point.

## Measure an area

An area is drawn in one slice. Select Area (shortcut O), then click the corners of an outline and close it by clicking the first point, double-clicking or pressing Enter. You can also press and drag to draw freehand, which closes when you let go. Backspace removes the last corner and Esc cancels.

The result is the flat area inside the outline in square millimetres, along with its perimeter. The points are flattened onto the plane of your first click, so scrolling the slice halfway through does not tilt the outline. A common use is the cross-sectional area of a structure in one slice.

## Measure a volume

The Volume tool works inside a space such as the airway or a sinus. Click inside it and the viewer selects the connected region around that point whose grey values are close to the one you clicked. It then multiplies the number of voxels by the volume of one voxel.

That makes the result a description of the region the tool selected, not of the structure as a whole. Where the region stops depends on the grey range, so check the highlighted region in the slices before you read the number. The [airway and sinuses guide](https://jawviewer.com/guide/airway-and-sinuses.md) covers the ready-made airway and sinus tools, and [what airway volume means](https://jawviewer.com/blog/airway-volume-cbct-what-it-means.md) explains why the boundaries change the figure.

## What does the grey value probe show?

The Grey value tool shows the brightness number under the pointer. It is useful for telling air from bone on a slice. On a CBCT scan it is not a calibrated density, and the viewer does not convert it; see [Hounsfield units and CBCT](https://jawviewer.com/blog/hounsfield-units-cbct-bone-density.md). On a medical CT the same number is in Hounsfield units.

## How far can you trust a number?

The reading is only as good as the points. In one study, 28 dry skulls were scanned and measured two ways, on panoramic reconstructions and directly on axial slices, then compared with calipers. On easily seen orthodontic wires the average error was under 1.2% with the panoramic technique and under 0.6% on axial slices.[1] Measurements between anatomical points were significantly more variable with either technique.[1]

A 2018 review of 22 studies, 2 of them clinical and 20 ex vivo, found a wide range of error, with both over- and underestimation against a gold standard.[2] A 2024 meta-analysis of low-dose protocols pooled a measurement error of -0.24 mm (95% CI -0.52 to 0.04), a tendency to read slightly short, with high heterogeneity.[3]

0.6 %

average error on wires, axial slices, 28 dry skulls (under)[1]

1.2 %

average error on wires, panoramic reconstruction (under)[1]

-0.24 mm

pooled error, low-dose protocols (95% CI -0.52 to 0.04)[3]

Those figures are from lab work, so they describe a best case. The 2018 authors name patient motion, metal artefacts, exposure settings, software and manual versus automated work as likely to lower accuracy in practice.[2] The full picture is in [how accurate CBCT measurements are](https://jawviewer.com/blog/how-accurate-are-cbct-measurements.md).

> Decimals are not precision
>
> Decimal places on screen do not mean the measurement is accurate to that many decimals. The [methods and limits page](https://jawviewer.com/limits.md) says what a number on screen depends on.

## From points to analyses

A cephalometric analysis is a set of distances and angles built from named landmarks you place by hand, so the same two- and three-point logic applies. [What a cephalometric analysis is](https://jawviewer.com/blog/what-is-a-cephalometric-analysis.md) goes through the best known ones, and [landmark placement error](https://jawviewer.com/blog/landmark-placement-error-cephalometry.md) covers why the same point lands in slightly different places each time. The [measuring guide](https://jawviewer.com/guide/view-and-measure.md) lists every tool, and measurements can be exported or saved in a project once you are done.

This is general information, not medical advice. Jaw Viewer is not a medical device. Talk to your surgeon, orthodontist or radiologist about your own case.

## Questions and answers

### How do I measure a distance on a CT scan?

Choose the distance tool, place one point at each end, and check both points in the slice views as well as in 3D. The reading is in millimetres, using the spacing recorded in the scan.

### Can I measure an angle on a CBCT scan?

Yes. Place three points, with the middle one at the vertex of the angle. The angle depends entirely on where you put those points, so check each one in the slices.

### Is a measurement on screen exact?

No. Reviews report a wide error range for CBCT linear measurements, both over and under. Most of that evidence is from skulls and other lab specimens, not living patients.

### Does the grey value mean bone density?

Not on a CBCT scan. The grey value is a brightness number that is not a calibrated density measure. On a medical CT the same readout is in Hounsfield units.

## Terms used

- **Voxel**: A three-dimensional pixel. A scan is a grid of voxels, each with one grey value.
- **Cross-sectional area**: The area of a flat slice through a structure, at right angles to its length. For the airway it is the open space at one height.
- **Hounsfield units**: The CT scale for how strongly a voxel blocks X-rays, with water at 0 and air near -1000.

## Sources

1. Ludlow JB, Laster WS, See M et al. (2007). Accuracy of measurements of mandibular anatomy in cone beam computed tomography images. Oral Surg Oral Med Oral Pathol Oral Radiol Endod, vol. 103(4), pp. 534-542. https://doi.org/10.1016/j.tripleo.2006.04.008 28 dry skulls compared with caliper measurements.
2. Fokas G, Vaughn VM, Scarfe WC et al. (2018). Accuracy of linear measurements on CBCT images related to presurgical implant treatment planning: A systematic review. Clin Oral Implants Res, vol. 29 Suppl 16, pp. 393-415. https://doi.org/10.1111/clr.13142 22 studies, 2 clinical and 20 ex vivo.
3. Carneiro ALE, Reis INR, Bitencourt FV et al. (2024). Accuracy of linear measurements for implant planning based on low-dose cone beam CT protocols: a systematic review and meta-analysis. Dentomaxillofac Radiol, vol. 53(4), pp. 207-221. https://doi.org/10.1093/dmfr/twae007 13 studies, 9 in the meta-analysis; the studies are in vitro.

---

Jaw Viewer (https://jawviewer.com). Page index for AI tools: https://jawviewer.com/llms.txt. Not a medical device.
